VEHICULAR WINDOW
NSN# 2510-01-435-9690 / 319 EACH/// 100% OPTION
OPEN/CLOSE: 6/12/14 - 7/14/14
************************************************************
WINDOW,VEHICULAR
52.246-11 Higher Level Contract Quality Requirement (Manufacturers)
FAR CLAUSE 52.246-11 APPLIES. A QUALITY MANAGEMENT PROGRAM MEETING THE
REQUIREMENTS OF ISO 9001:2008; A PROGRAM COMPARABLE TO ISO 9001:2008
(EXAMPLE SAE AS 9100), THE FOLLOWING TAILORED VERSION OF ISO 9001:2008;
OR A PROGRAM COMPARABLE TO THE TAILORED VERSION OF ISO 9001:2008
(EXAMPLE SAE AS 9003) IS REQUIRED. IN THE TAILORED VERSION OF THE ISO
9001:2008, ANY REFERENCES WHICH CITE THE ENTIRE INTERNATIONAL STANDARD
ARE INTERPRETED AS EXCLUSIONS TO THIS DOCUMENT.
DLA TAILORED HIGHER LEVEL QUALITY CLAUSE FROM ISO 9001:2008
4.1 General requirements, [excluding reference to 1.2 and excluding NOTE
3 c)]
4.2.1 General, [excluding subparagraph a)]
4.2.2 Quality manual, [excluding subparagraph a)]
4.2.3 Control of documents
4.2.4 Control of records
5.1 Management commitment
5.3 Quality policy
6.2.2 Competence, training and awareness
6.4 Work environment
7.1 Planning of product realization, [excluding NOTE 2]
7.2.1 Determination of requirements related to the product
7.2.2 Review of requirements related to the product
7.2.3 Customer communication
7.3.7 Control of design and development changes
7.4.1 Purchasing process
7.4.3 Verification of purchased product
7.5.1 Control of production and service provision
7.5.3 Identification and traceability
7.5.4 Customer property
7.5.5 Preservation of product
7.6 Control of monitoring and measuring equipment
8.1 General, [excluding subparagraph b) and subparagraph c)]
8.2.2 Internal audit
8.2.4 Monitoring and measurement of product
8.3 Control of nonconforming product
8.5.2 Corrective action
8.5.3 Preventive action
DISPOSITION:
IF FAR 52.209-3 (e) APPLIES "THE CONTRACTOR MAY DELIVER THE APPROVED
FIRST ARTICLE AS PART OF THE CONTRACT QUANTITY#" THEN THE PS DOES NOT
HAVE TO ENTER ANYTHING IN THE POT. IF DISPOSITION IS DIFFERENT, ENTER
DISPOSTION INSTRUCTIONS-
"PER DLAD 52.209-9017, ALT III DISPOSITION OF FIRST ARTICLES:
THE CONTRACTOR SHALL RETAIN ALL FIRST ARTICLE UNITS AS PRODUCTION
STANDARDS.
FAT CALLED OUT DRAWING 12512211, #9A
REQUIRED BY ATPD 2352
IMPORTANT NOTE; THIS ITEM REQUIRES CONTRACTOR
FIRST ARTICLE TESTING AND GOVERNMENT BALLISTIC
TESTING AS INSTRUCTED PER DRAWING 12512211 AND
ATPD 2352. THE RESULTS FROM THIS REQUIRED
TESTING MUST BE AVAILABLE FOR REVIEW BY A
GOVERNMENT REPRESENTATIVE BEFORE ACCEPTANCE.
ALL SUPPLIERS MUST MEET ATPD 2352, "4.1.3
PRODUCTION CONTROL TEST" REQUIREMENTS WHICH
APPLIES TO THE MATERIAL PRODUCTION LOT.
THIS APPLIES WHETHER FIRST ARTICLE IS
REQUIRED OR NOT.
THE GLASS THICKNESS SHOULD BE 53mm.
THIS NSN REQUIRES GOVERNMENT SOURCE INSPECTION
WITH A FIRST ARTICLE TEST REQUIREMENT. THE
GOVERNMENT SOURCE INSPECTION REQUIREMENT IS
VALID ONLY WHEN AN AWARD IS MADE INVOKING THE
FIRST ARTICLE TEST REQUIREMENT. IF THE AWARD
DOES NOT INCLUDE THE FAT REQUIREMENT, INSPECTION
AT DESTINATION IS ACCEPTABLE.
THIS NSN CONTAINS ONE OR MORE COMPONENTS WHICH
MUST MEET QPL/QML SPECIFICATIONS.BY SUBMITTING
AN OFFER, THE OFFEROR AGREES TO PROVIDE QPL/QML
COMPONENTS ONLY FROM SOURCES QUALIFIED ON THE
APPLICABLE QPL(S)/QML(S).
FULL AND OPEN COMPETITION APPLY
IF AQLS ARE LISTED IN THE SPECIFICATION(S)
OR DRAWING(S) THEY MAY BE USED TO ESTABLISH THE
AUTHORIZED SAMPLE SIZE,HOWEVER,THE ACCEPTANCE
NUMBER FOR THIS CONTRACT IS ZERO;I.E.,THIS
CONTRACT REQUIRES A SAMPLING PLAN THAT ACCEPTS
ON ZERO DEFECTS AND REJECTS ON ONE OR MORE
DEFECT(S).
IF THE APPLICABLE (OEM OR MILITARY) DRAWING,
SPECIFICATION, STANDARD, OR QUALITY ASSURANCE
PROVISION (QAP) SPECIFIES AN ACCEPTABLE QUALITY
LEVEL (AQL), THE SAMPLING ACCEPTANCE NUMBER
SHALL BE REDUCED TO ZERO (0). FOR EXAMPLE, IF
THE ACCEPT REJECT CRITERIA IS ACCEPT ON (3)
DEFECTS AND REJECT ON (4) DEFECTS, THE NEW
ACCEPT REJECT CRITERIA IS ACCEPT ON (0) DEFECTS
AND REJECT THE ENTIRE LOT ON (1) DEFECT. EVEN
THOUGH THE ACCEPTANCE LEVEL IS ELIMINATED, THE
SAMPLE SIZE REMAINS THE SAME.
THE ITEM DESCRIBED IN THIS SOLICITATION
IS DEFINED IN WHOLE OR IN PART BY ARMY
DRAWING(S). THESE DRAWING(S) MAY CONTAIN
A PAINT FINISHING REQUIREMENT. WHERE SUCH
REQUIREMENTS ARE SPECIFIED, USE DCSC DRAWING
16236 CS-2300-0001 IN LIEU OF FINISH REQUIRE-
MENTS OF THE ARMY DRAWING(S). THIS DRAWING
CONTAINS SPECIFICATIONS FOR CHEMICAL AGENT
RESISTANT COATINGS (CARC), AND ADDITIONAL
INFORMATION RELATING TO HIGH TEMPERATURE
COATINGS.
THIS ITEM HAS TECHNICAL DATA SOME OR ALL OF WHICH IS SUBJECT TO
EXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE TECHNICAL DATA
AND ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE SUPPLIERS QUALIFIED
THROUGH JCP CERTIFICATION, OR TO THOSE LICENSED BY EITHER THE
DEPARTMENTS OF STATE OR COMMERCE; OR TO FOREIGN SUPPLIERS PURSUANT TO
INTERNATIONAL AGREEMENTS.
TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM 2345, "MILITARY
CRITICAL TECHNICAL DATA AGREEMENT," FORM IS AVAILABLE AT THE WORLD WIDE
WEB ADDRESS HTTP://WWW.DLIS.DLA.MIL/JCP OR BY WRITING TO:
DLA LOGISTICS INFORMATION SERVICE
FEDERAL CENTER
74 WASHINGTON AVE., NORTH
BATILE CREEK, MI 49017-3084
TO MANUFACTURE THIS ITEM, NON-JCP CERTIFIED SUPPLIERS MUST SUBMIT A
CURRENT MANUFACTURING LICENSE AGREEMENT, TECHNICAL ASSISTANCE AGREEMENT,
DISTRIBUTION AGREEMENT OR OFF-SHORE PROCUREMENT AGREEMENT APPROVED BY
THE DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THE OFFER, UNLESS AN
EXEMPTION UNDER THE PROVISIONS OF ITAR SECTION, 125.4 "EXEMPTIONS OF
GENERAL APPLICABILITY," AND/OR EAR PART 740 ARE APPLICABLE.
NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT CONTROLLED TECHNICAL
DATA ARE REQUIRED TO PROVIDE THE CONTRACTING OFFICER WITH AN
APPLICABLE AGREEMENT OR IDENTIFY WHICH ITAR/EAR EXEMPTION APPLIES TO
RECEIVE A COPY OF THE EXPORT CONTROLLED TECHNICAL DATA.
NOTE: JCP CERTIFIED CONTRACTORS WHO RECEIVE TECHNICAL DATA PURSUANT TO
THEIR DD FORM 2345 CERTIFICATION MAY NOT FURTHER DISSEMINATE SUCH DATA
UNLESS FURTHER DISSEMINATION OF THE TECHNICAL DATA IS EXPRESSLY
PERMITTED BY DODD 5230.25."
IAW BASIC DRAWING NR 19207 12512211
REVISION NR DTD 03/17/2008
PART PIECE NUMBER: 12512211-1
IAW REFERENCE DRAWING NR 19207 12369003
REVISION NR G DTD 05/14/2007
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 19207 12512211-1
REVISION NR DTD 05/03/2012
PART PIECE NUMBER:
Michele Beasley, Phone 6146927572, Email [email protected]
