Sweaters Various Items
CLIN: 0001
PGC: 02765
NSN: 8405-01-496-9808(s)
SWEATER, MARINE CORPS
SWEATER, SERVICE WOOL (WITH EPAULETTES)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
ADDITIONAL INFORMATION FOR A-A-55239:
.
STANDARD SHADE SAMPLES:
MC SHADE 2247,ROLL NO. 059-96 IS
REFERENCED FOR SHADE, FINISH, AND
COLORFASTNESS FOR SWEATER YARNS.
.
MC SHADE 2248, ROLL NO. 5-2886 IS
REFERENCED FOR SHADE, FINISH AND
COLORFASTNESS FOR THE ARM PATCH AND
EPAULETTES.
.
INSPECTION LEVELS AND AQL S
THE INSPECTION LEVELS AND THE AQL S EXPRESSED IN
DEFECTS PER ONE HUNDRED UNITS (DHU) FOR VISUAL
AND DIMENSIONAL EXAMINATION,SHALL BE AS FOLLOWS
. INSPECTION LEVEL TOTAL DEFECTS
FOR VISUAL EXAMINATION II 6.5
FOR DIMENSIONAL EXAMINATION
. S-3 2.5
.
DEVIATIONS TO A-A-55239A:
.
PARAGRAPH 3.7, TABLE III. FINISHED
MEASUREMENTS. FOR THE COLUMN TITLED
"SKIRT WIDTH", UNDER TOLERANCE DELETE
"PLUS OR MINUS 1/2" AND SUBSTITUTE
"PLUS OR MINUS 1".
.
THE FOLLOWING NEW PARAGRAPHS SHALL BE ADDED:
.
EPAULETTES. THE EPAULETTES SHALL FINISH
SMOOTH AND FLAT AND BE UNIFORM IN
CONSTRUCTION AND PLACEMENT. THE EPAULETTES
SHALL BE MADE FROM TWO PLIES OF THE SAME
FABRIC USED FOR THE SHOULDER AND ELBOW
PATCHES AND SHALL BE SEWN TOGETHER WITH EDGES
TURNED IN BY LOCKSTITCHING (STITCH TYPE 301)
WITH AT LEAST 10 STITCHES PER INCH OF SEAM
AND SHALL FINISH 2 INCHES WIDE AT THE ARMHOLE
SEAM TAPERING TO 1-3/4 INCHES WIDE AT THE
ROUNDED END. PRIOR TO STITCHING THE TWO PLIES
OF THE EPAULETTE, A PATCH OF LOOP PILE FABRIC
3/4 INCH LONG IS TO BE SEWN 1/4 - 3/8 INCH
(CENTERED) FROM THE ROUNDED END OF THE
UNDERPLY OF EPAULETTE. POSITION THE EPAULETTE
SO AS THE ROUND END OF LOOP IS 3/8 INCH BEYOND
THE COLLAR SEAM WITH THE BACK FINISHED EDGE
OF THE EPAULETTE ON THE FINISHED SWEATER
(SWEATER IN RELAXED STATE) SHALL BE 1/2 INCH
BEHIND THE SHOULDER SEAM. THE EPAULETTE IS
INSERTED INTO THE SLEEVE SETTING SEAM. THE
HOOK TAPE SHALL BE MOVED TO MATCH THE LOOP
PILE ON THE EPAULETTE. FOR SWEATER SIZES
28 THROUGH 32, THE LOOP PILE FABRIC PIECE MAY
BE 1/2 TO 1/2 SQUARE AND SHALL BE STITCHED AS
CLOSE TO THE END OF THE EPAULETTE AS POSSIBLE.
ON THE UNDERSIDE OF EPAULETTE, THE INNER EDGE
OF LOOP PILE FABRIC TO SLEEVE SETTING SHALL
MEASURE A MINIMUM OF 3-5/8 INCHES. A 3/4 INCH
LONG PIECE OF HOOK FABRIC IS TO BE SEWN ON
THE SHOULDER PATCH ABUTTING THE EDGE OF THE
NECKBAND IN ALIGNMENT WITH THE LOOP FABRIC
ON THE UNDERSIDE OF THE EPAULETTE ADHERING
TO CLEARANCE MEASUREMENT AS DESCRIBED ABOVE.
THE EPAULETTE SHALL LIE SMOOTH AND FLAT OVER
SHOULDER PATCH WHEN THE LOOP AND PILE FABRICS
ARE ENGAGED. NO FUSIBLE IS REQUIRED.
.
HOOK AND LOOP. THE HOOK AND LOOP FOR ALL THE
SWEATER SIZES SHALL BE 5/8 INCH WIDE BY 3/4 INCH
LONG, TYPE I, CLASS 1, NYLON, IN ACCORDANCE WITH
A-A-55126. THE SHADE OF THE HOOK AND LOOP
SHALL APPROXIMATE THE SHADE OF THE EPAULETTE
FABRIC.
.
SWEATER (WITH EPAULETTES) WEIGHTS. THE WEIGHTS
PER SIZE (EXPRESSED IN POUNDS) AND BASED ON 12
SWEATERS SHALL BE AS FOLLOWS:
.
28/30 11-1/4
32/34 13
36 14-1/2
38 15-1/4
40 17-3/8
42 18-1/8
44 19-1/4
46 20
48 20-3/4
50 21-1/2
.
THE TOLERANCE ON THE WEIGHT FOR THE SWEATER
(WITH EPAULETTES) IS PLUS OR MINUS 1/4
POUND.
.
ADD THE NEW FIGURE TO BACK OF DOCUMENT.
FIGURE 3. SWEATER, SERVICE, WOOL, EPAULETTES
(Ref. W2765)
.
"MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,
AND TENTAGE, GENERAL USE REPLACES DDD-L-20
(Ref. T0451 - June 19, 2007)
INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:
PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE
TYPE VI FINISHED LABEL." UNDER "TEARING
STRENGTH" DELETE: "(LB.) MINIMUM" AND
SUBSTITUTE: "(GNS) MINIMUM."
PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD
"AND THE UNIVERSAL PRODUCT CODE (UPC)
SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."
MIL-STD-129R - DEPARTMENT OF DEFENSE STANDARD PRACTICE
- MILITARY MARKING FOR SHIPMENT AND STORAGE
DATED 18 FEBRUARY 2014
INTERIM CHANGES:
OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS
IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:
THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.
IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.
MIL-STD-147E
w/CHANGE 1
23 December 2013
SUPERSEDING
MIL-STD-147E
16 May 2008
DEPARTMENT OF DEFENSE
STANDARD PRACTICE
PALLETIZED UNIT LOADS
ADDITIONAL INFORMATION FOR MIL-STD-2073-1:
.
NO ADDITIONAL INFORMATION FOLLOWS
(Ref. T0898)
ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:
NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.
APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:
AMERICAN SOCIETY FOR QUALITY
600 NORTH PLANKINTON AVENUE
MILWAUKEE, WISCONSIN 53203
(Ref. T0795 - May 17, 2006)
ADDITIONAL INFORMATION FOR A-A-52094A THREAD, COTTON
NO ADDITIONAL INFORMATION
(ref. T1481)
CLIN: 0002
PGC: 02408
NSN: 8405-01-445-6907(s)
SWEATER, COAST GUARD
SWEATER, WOOL, PULL-OVER STYLE, V-NECK,
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
AIR FORCE BLUE 1594
.
ADDITIONAL INFORMATION FOR PD AESC 86-1:
.
STANDARD SAMPLE FOR SHADE AND COLORFASTNESS FOR
THE WOOL SHADE AF.1594 SHALL BE ROLL 229082011
.
STANDARD SAMPLE FOR SHADE ONLY FOR ARM AND
SHOULDER PATCHES SHALL BE ROLL NO.2
AIR FORCE BLUE SHADE 1582.
.
.
INSPECTION LEVELS AND AQL'S EXPRESSED IN
DEFECTS PER 100 UNITS FOR VISUAL AND
DIMENSIONAL EXAMINATIONS.
ANSI/ASQC Z1.4 GENERAL INSPECTION
. LEVEL 11-VISUAL- 6.5 TOTAL DEFECTS
. LEVEL S3- DIMENSIONAL - 2.5 TOTAL DEFECTS.
(Ref. W2408)
.
DELETE CURRENT "BARCODE LABEL/TAG" REQUIREMENTS AND SUBSTITUTE THE FOLLOWING:
LABEL TAG: EACH ITEM SHALL BE INDIVIDUALLY BAR-CODED WITH A PAPER TAG FOR PERSONAL CLOTHING ITEMS. THE PAPER USED FOR THE TAGS SHALL BE STANDARD BLEACHED SULFATE HAVING A BASIS WEIGHT OF 100 POUNDS WITH A SMOOTH FINISH TO ACCEPT THERMAL TRANSFER AND DIRECT PRINTING. THE TAGS SHALL HAVE A HOLE AND SHALL BE ATTACHED TO EACH ITEM BY A FASTENER, CLEARLY LEGIBLE AND READABLE BY SCANNER. THE BAR CODING ELEMENT SHALL BE A 13 DIGIT
NATIONAL STOCK NUMBER (NSN). THERE SHALL BE A 12 DIGIT UNIVERSAL PRODUCT CODE (UPC) ASSIGNED FOR ALL NSNS BY THE GOVERNMENT. THE INITIAL "UPC" MUST APPEAR BENEATH THE CODE. THE BAR CODES FOR NSN AND UPC SHALL BE A MEDIUM TO HIGH DENSITY AND SHALL BE LOCATED SO THAT THEY ARE COMPLETELY VISIBLE ON THE ITEM WHEN IT IS FOLDED AND PACKAGED AS SPECIFIED. THE LABEL'S LOCATION SHALL CAUSE NO DAMAGE TO THE ITEM.
NOTE: UNIVERSAL PRODUCT CODE INFORMATION THE GOVERMENT ASSIGNED UNIVERSAL PRODUCT CODE (UPC) MUST BE PLACED ON ALL SHIPPING CARTONS ON WHICH THE NSN APPEARS.
THE FOLLOWING DEFECTS APPLY FOR BARCODE LABELS/TAGS:
BAR CODE OMITTED OR NOT READABLE BY SCANNER
HUMAN-READABLE INTERPRETATION (HRI) OMITTED OR ILLEGIBLE
NOT VISIBLE ON FOLDED, PACKAGED ITEM CAUSES DAMAGE TO THE ITEM
NOTE: IF THE END ITEM IS PLACED IN A PLASTIC BAG - USE TYPE VII (PRESSURE SENSTIVE LABEL) OF MIL-DTL-32075.
IF THE END ITEM IS TIED IN A BUNDLE OR LEFT AS AN INDIVIDUAL ITEM, USE TYPE VIII (TAG, PAPER) OF MIL-DTL-32075.
ADDITIONAL INFORMATION FOR V-B-871: NO ADDITIONAL INFORMATION FOLLOWS.
ADDITIONAL INFORMATION FOR V-T-276:
V-T-276 HAS BEEN CANCELLED AND REPLACED BY
A-A-52094
"MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,
AND TENTAGE, GENERAL USE REPLACES DDD-L-20
(Ref. T0451 - June 19, 2007)
INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:
PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE
TYPE VI FINISHED LABEL." UNDER "TEARING
STRENGTH" DELETE: "(LB.) MINIMUM" AND
SUBSTITUTE: "(GNS) MINIMUM."
PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD
"AND THE UNIVERSAL PRODUCT CODE (UPC)
SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."
ADDITIONAL INFORMATION FOR DDD-T-86:
.
INTERIM CHANGES TO DDD-T-86H:
.
NOTE - REDUCED AQLS APPLY AS FOLLOWS:
PAGE 9, LINE 9, DELETE "0.4" AND SUBSTITUTE,
"0.28", FOR MAJORS. DELETE "1.5" AND SUBSTITUTE
"1.0", FOR TOTALS.
.
COMMERCIAL ITEM DESCRIPTION A-A-52071
DATED 25 APRIL 1990 HAS BEEN AUTHORIZED FOR
USE IN PLACE 0F DDD-T-86H.
"THE REQUIREMENT FOR THE HERRINGBONE TAPE IS TYPE I, 3/16 INCH WIDTH AND 58 PICKS PER INCH FROM TABLE I. PHYSICAL REQUIREMENTS."
MIL-STD-1186A CUSHIONING, ANCHORING, BRACING,
. BLOCKING, & WATERPROOFING WITH
. APPROPRIATE TEST METHODS,
. 3/12/81, NOT 1, 1/9/90
ADDITIONAL INFORMATION FOR MIL-C-29127:
.
INTERIM SPEC CHANGES TO MIL-C-29127A:
.
PAGE 2
PARA. 3.1 STANDARD SAMPLE. ADD THE FOLLOWING
SENTENCE: "THE STANDARD SAMPLE FOR BLUE 3362 IS
IDENTIFIED UNDER PIECE NO. 78349, FOR KHAKI
3729 UNDER PIECE NO. 89216 AND FOR WHITE 3053
UNDER PIECE NO. 02092.
.
PAGE 3
PARA. 3.4.1, DELETE PARAGRAPH AND SUBSTITUTE:
"3.4.1 CLASS 1, DYED. UNLESS OTHERWISE SPECIFIED
(SEE 6.2) THE COLOR OF THE DYED CLOTH SHALL
MATCH THE APPLICABLE SHADE STANDARD (SEE 3.1).".
.
PAGE 6
ADD NEW PARAGRAPH: "4.4.2.5 EXAMINATION FOR
SHADE MATCH AND FINISH, INDIVIDUAL ROLLS.
EACH ROLL IN THE LOT SHALL BE EXAMINED VISUALLY
FOR SHADE MATCH (SEE 3.4.3) AND FINISH (SEE 3.7)
A ROLL SHALL BE UNACCEPTABLE IF IT FAILS TO MEET
THE REQUIREMENTS FOR SHADE MATCH OR FINISH. THE
SAMPLE UNIT SHALL BE A 4 INCH BY 20 INCH (10.2
BY 50.8 CM) SWATCH OF THE CLOTH. A SAMPLE UNIT
SHALL BE DRAWN FROM EACH ROLL IN THE LOT."
.
PAGE1, PARA 2.1 LINE 8, DELETE "MIL-T-43548-
THREAD POLYESTER, COTTON-COVERED MIL-T-43624-
THREAD POLYESTER SPUN"
.
PAGE 2, AFTER PARA 2.1 INSERT THE FOLLOWING NEW
PARAGRAPH:
"2.2 NON-GOVERNMENT PUBLICATIONS. THE
FOLLOWING DOCUMENTS FORM A PART OF THIS
DOCUMENT TO THE EXTENT SPECIFIED HEREIN. UNLESS
OTHERWISE SPECIFIED, THE ISSUES OF THE
DOCUMENTS WHICH ARE DOD ADOPTED ARE THOSE LISTED
IN THE ISSUE OF THE DODISS CITED IN THE
SOLICITATION. UNLESS OTHERWISE SPECIFIED, THE
ISSUES OF DOCUMENTS NOT LISTED IN THE DODISS ARE
THE ISSUES OF THE DOCUMENTS CITED IN THE
SOLICITATION (SEE 6.2).
.
AMERICAN NATIONAL STANDARDS INSTITUTE/AMERICAN
SOCIETY FOR QUALITY (ANSI/ASQ)
ANSI/ASQ Z1.4 SAMPLING PROCEDURES AND TABLES
FOR INSPECTION OF ATTRIBUTES.
(APPLICATION FOR COPIES SHOULD BE ADDRESSED TO
AMERICAN NATIONAL STANDARDS INSTITUTE,
11 WEST 42ND STREET, NEW YORK, NY 10036-8002).
.
AMERICAN ASSOCIATION OF TEXTILE CHEMISTS &
COLORISTS (AATCC)
AATCC-8 -COLORFASTNESS TO CROCKING
AATCC-15 - COLORFASTNESS TO PERSPIRATION
AATCC-16 -COLORFASTNESS TO LIGHT
AATCC-20 - FIBER ANALYSIS: QUANTITATIVE
AATCC-61 -COLORFASTNESS TO LAUNDERY, HOME
. AND COMMERCIAL: ACCELERATED
AATCC-81 -PH OF THE WATER-EXTRACT FROM
. BLEACHED TEXTILES
AATCC-96 -DIMENSIONAL CHANGES IN COMMERCIAL
. LAUNDERING OF WOVEN AND KNITTED
. FABRICS
AATCC-124 -APPEARANCE OF FABRICS AFTER REPEATED
. HOME LAUNDERINGS
AATCC-132 -COLORFASTNESS TO DRY-CLEANING
AATCC-135 -DIMENSIONAL CHANGES IN AUTOMATIC
. HOME LAUNDERINGS OF WOVEN AND KNIT
. FABRICS
.
(APPLICATIONS FOR COPIES SHOULD BE ADDRESSED TO:
AMERICAN ASSOCIATION OF TEXTILE CHEMIST AND
COLORISTS, P.O. BOX 12215, TRIANGLE PARK, NC
27709-2215)
.
AMERICAN SOCIETY FOR TESTING AND MATERIAL (ASTM)
.
ASTM-D-747 -APPARENT BENDING MODULUS OF
. PLASTICS BY MEANS OF A CANTILEVER
. BEAM
ASTM-D-1424 -TEAR RESISTANCE OF WOVEN FABRICS BY
. FALLING PENDULUM (ELMENDORF)
. APPARATUS
ASTM-D-3775 -FABRIC COUNT OF WOVEN FABRICS
ASTM-D-3776 -MASS PER UNIT AREA (WEIGHT) OF
. FABRIC
ASTM-D-5034 -BREAKING FORCE, AND ELONGATION
. OF TEXTILE FABRICS
.
(APPLICATIONS FOR COPIES SHOULD BE ADDRESSED TO:
AMERICAN SOCIETY FOR TESTING AND MATERIALS,100
BARR HARBOR DRIVE, WEST CONSHOHOCKEN PA.19428-
2959)"
.
PAGE 2, LINE 7, DELETE "MIL-STD-105- SAMPLING
PROCEDURES AND TABLES FOR INSPECTION BY
ATTRIBUTES"
PAGE 2,PARA 3.3.2,DELETE IN ITS ENTIRETY.
PAGE 3,PARA 3.4.1.1,DELETE IN ITS ENTIRETY.
PAGE 3, PARA 3.4.1.2,DELETE IN ITS ENTIRETY.
PAGE 3, PARA 3.4.2.1,DELETE IN ITS ENTIRETY.
PAGE 3, PARA 3.4.3,DELETE IN ITS ENTIRETY, AND
SUBSTITUTE "MATCHING. THE COLOR AND
APPEARANCE OF THE DYED AND FINISHED CLOTH SHALL
MATCH THE STANDARD SAMPLE WHEN VIEWED UNDER
FILTERED TUNGSTEN LAMPS WHICH APPROXIMATE
ARTIFICIAL DAYLIGHT HAVING A CORRELATED COLOR
TEMPERATURE OF 7500K (+OR-200K) WITH
ILLUMINATION OF 100(+ OR - 20) FOOT CANDLES,
AND SHALL BE A GOOD MATCH TO THE STANDARD SAMPLE
UNDER INCANDESCENT LAMPLIGHT AT 2300K(+OR-200K)"
PAGE 3,PARA 3.5, LINE 3, TABLE 1- PHYSICAL
REQUIREMENTS, DELETE IN IT'S ENTIRETY, AND
SUBSTITUTE" TABLE 1- PHYSICAL REQUIREMENTS.
.
CHARACTERISTIC REQUIREMENTS
YARN PLY SINGLES
WEAVE 2/1 LEFT HAND TWILL
FIBER CONTENT 65+OR-5% POLYESTER
. WITH THE REMAINING
. % COTTON
SULFUR CONTENT NO MORE THAN SLIGHT
COLORFASTNESS TO:
.LAUNDERING (3 CYCLES) NOT LESS THAN GRADE 3
.PERSPIRATION NOT LESS THAN GRADE 3
.LIGHT (40 HRS) NOT LESS THAN GRADE 3
.CROCKING NOT LESS THAN 3
.
DISCOLORATION TO:
.LAUNDERING (3CYCLES) NOT LESS THAN GRADE 3
.PERSPIRATION NOT LESS THAN GRADE 3
.LIGHT (40 HRS) NOT LESS THAN GRADE 3
.WET-DRY CLEANING NOT LESS THAN GRADE 3
.COMBINED LAUNDERING
.AND BLEACHING NOT LESS THAN GRADE 3
.WEIGHT,OZ/SQUARE YD. 7.5 TO.8.2
YARNS PER INCH,MIN.
. WARP 85
. FILLING 48
.BREAKING STRENGTH,LBS (MIN.)
. WARP 190
. FILLING 110
STIFFNESS, IN-LBS (MAX)
. WARP .002
. FILLING .002
TEAR STRENGTH,LBS (MIN)
. WARP 7.0
. FILLING 5.0
NON-FIBROUS MATERIAL,% MAX. 6.0
DIMENSIONAL STABILITY,
. WARP AND FILLING
. AFTER 5 CYCLES,% MAX. 2.5
SOIL RELEASE NOT LESS THAN 3.0
DURABLE PRESS AFTER 5 CYCLES
. NOT LESS THAN DP 3.0
PH 5 - 8.5
ALL OF THE ABOVE REQUIREMENTS ARE UNDER
VERIFICATION PARAGRAPH 4.5".
.
PAGE 4,PARA 3.5.2,DELETE IN ITS ENTIRETY.
PAGE 4,3.6,DELETE IN IT'S ENTIRETY, AND
SUBSTITUTE "3.6 FINISH. THE CLOTH SHALL BE
DESIZED, SCOURED, BLEACHED (FOR CLASS 2 ONLY),
THE WHITE 3053 SHALL BE OBTAINED WITH A
CHEMICAL BLEACH. WHEN FLUORESCENT OPTICAL
BRIGHTENERS ARE USED, THEY SHALL FLUORESCE TO
THE BLUE REGION. THE CLOTH SHALL BE TREATED
WITH A PRECURED DURABLE PRESS RESIN AND A
SOIL RELEASE TREATMENT TO OBTAIN A HAND EQUAL
IN CHARACTERISTICS TO THAT OF THE STANDARD
SAMPLE. THE RESIN FINISH SHALL BE A NON-
CHLORINE RETENTIVE TYPE."
PAGE 4,PARA 3.7,DELETE IN IT'S ENTIRETY.
PAGE 4,PARA 3.8,DELETE IN ITS ENTIRETY.
PAGE 4,PARA 3.9 DELETE IN ITS ENTIRETY.
PAGE 4,PARA 3.10,DELETE IN ITS ENTIRETY.
.
PAGE 5,PARA 4.4,LINE 2,DELETE "MIL-STD-105"
. AND INSERT "ANSI/ASQ Z1.4"
PAGE 5,PARA 4.1.1, DELETE IN IT'S ENTIRETY.
.
PAGE 7,TABLE 11-TEST METHOD, DELETE IN ITS
ENTIRETY AND SUBSTITUTE:
. "TABLE 11 - TEST METHOD
CHARACTERISTIC 1/ REQ. PARA.
YARN PLY 3.5
. TEST METHOD VISUAL
WEAVE 3.5
. TEST METHOD VISUAL 2/
FIBER CONTENT 3.5
. TEST METHOD ATCC 20A
SULFUR CONTENT 3.5
. TEST METHOD FED-STD-191A
COLORFASTNESS TO:
.LAUNDERING (3 CYCLES) 3.5
. TEST METHOD AATCC 61 TEST 3A 3/ 4/
.PERSPIRATION 3.5
. TEST METHOD AATCC 15 4/
.LIGHT (40 HRS) 3.5
. TEST METHOD AATCC 16 OPT A
.CROCKING 3.5
. TEST METHOD AATCC 8
DISCOLORATION TO:
.LAUNDERING (3 CYCLES) 3.5
TEST METHOD AATCC 61 TEST 3A 3/ 4/
PERSPIRATION 3.5
.LIGHT 3.5
. TEST METHOD AATCC 16 OPT A
.WET-DRY CLEANING 3.5
. TEST METHOD AATCC 132
COMBINED LAUNDERING AND BLEACHING 3.5
. TEST METHOD AATCC-61 TEST 4A 4/
WEIGHT,OZ/SQ.YD 3.5
. TEST METHOD ASTM D3776 OPT C
YARNS PER INCH,MIN. 3.5
. TEST METHOD ASTM D3775
BREAKING STRENGTH, 3.5
. TEST METHOD ASTM D5034
STIFFNESS, 3.5
. TEST METHOD ASTM D747
TEAR STRENGTH, 3.5
. TEST METHOD D1424
NON-FIBROUS MATERIAL,% MAX. 3.5
. TEST METHOD AATCC 20A
DIMENSIONAL STABILITY, WARP & FILL 3.5
. TEST METHOD AATCC 135 (3)VAIII
.
AFTER 5 CYCLES,% MAX.
SOIL RELEASE 3.5 TEST METHOD 4.5.1.2
DURABLE PRESS AFTER 5 CYCLES 3.5
. TEST METHOD AATCC 124 (3)VAIII
PH 3.5 TEST METHOD AATCC-81
FOOTNOTES:
1/ TESTING SHALL BE PERFORMED UNDER STANDARD
ATMOSPHERIC CONDITIONS FOR TEXTILES AS
SPECIFIED IN ASTM D1776 (TEMPERATURE OF 70
DEGREES F +OR- 2 DEGREES F AND A RELATIVE
HUMIDITY OF 65 PERCENT +OR-2 PERCENT).
.
2/ ONE DETERMINATION SHALL BE MADE FROM EACH
SAMPLE UNIT AND THE RESULT SHALL BE REPORTED AS
"PASS" OR "FAIL".
.
3/ THE SPECIMEN MUST BE DRIED AFTER EACH OF THE
3 LAUNDERING CYCLES.
.
4/ ONLY THE STAINING ON THE COTTON AND
POLYESTER STRIPES OF THE COLOR TRANSFER CLOTH
SHALL BE EVALUATED."
.
PAGE 8, PARA 4.5.1.1,AFTER 4.5.1.1 INSERT THE
FOLLOWING NEW PARAGRAPHS:
"4.5.1.2 SOIL RELEASE TEST PROCEDURE. THE TEST
SHALL BE IN ACCORDANCE WITH THE REQUIREMENTS
BELOW.
.
4.5.1.2.1 SPECIMENS. THERE SHALL BE THREE (3)
4X8 INCH SPECIMENS TAKEN FROM DIFFERENT WARP
AND FILLING YARNS.
.
4.5.1.2.2 STAINING. THE TEST SPECIMENS SHALL
BE STAINED IN ACCORDANCE WITH AATCC TM 130,
EXCEPT FOR THE FOLLOWING: THREE DROPS OF
GRAPHITE MULTI-GRADE MOTOR OIL (SAE 10W-40),
SUPPLIED AS GFM (SEE 6.4.1),SHALL BE USED IN
LIEU OF FIVE DROPS OF MINERAL OIL.
.
4.5.1.2.3 LAUNDERING. THE TEST SPECIMENS
SHALL BE LAUNDERED IN ACCORDANCE WITH AATCC
TM 61,TEST NO.111A,EXCEPT FOR THE FOLLOWING:
(1) THE TOTAL LIQUOR VOLUME SHALL BE 500 ML.
(2) FIFTEEN GRAMS PER LITER OF AATCC (124
WOB) DETERGENT SHALL BE USED. (3) A TOTAL OF
50 STAINLESS STEEL BALLS SHALL BE USED. (4)
NO MULTI-FIBER TEST FABRIC OR BLEACHED COTTON
FABRIC IS REQUIRED. (5) AT THE END OF THE CYCLE,
RINSE IN RUNNING WATER AT 105 DEGREES F, FOR
FIVE MINUTES. NO SCOURING IS REQUIRED. (6)
HYDROEXTRACT THE TEST SPECIMEN TO REMOVE EXCESS
MOISTURE. AIR DRY OR OVEN DRY AT 220 DEGREES F.
.
4.5.1.2.4 EVALUATION. THE TEST SPECIMEN SHALL
BE EVALUATED IN ACCORDANCE WITH AATCC TM 130
PROCEDURE, EXCEPT IT SHALL BE EVALUATED
AGAINST "NCTRF STAIN RELEASE REPLICA",
SUPPLIED AS GFM (SEE 6.4.2). THE TREATED
SPECIMENS SHALL HAVE AN AVERAGE SOIL RELEASE
RATING OF NOT LESS THAN 3.0 WHEN TESTED AS
SPECIFIED."
.
PAGE 8, PARA 4.5.1,DELETE IN IT'S ENTIRETY.
PAGE 8, PARA 4.5.1.1. DELETE IN IT'S ENTIRETY.
.
PAGE 9,FOLLOWING 6.4 INSERT THE FOLLOWING NEW
PARAGRAPH:
"6.4.1 GOVERNMENT FURNISHED MATERIAL(GFM) THE
GRAPHIC MULTI-GRADE MOTOR OIL,AND THE NCTRF
STAIN RELEASE REPLICA ARE AVAILABLE AFTER
AWARD OF CONTRACT FROM THE PROCURING OFFICE
ISSUING THE INVITATION FOR THE BIDS.
.
PAGE 9,FOLLOWING 6.4.1,DELETE "CUSTODIAN :
NAVY -SA",AND INSERT "CUSTODIAN :
NAVY- NU"
.
ADDITIONAL INFORMATION FOR MIL-T-43548:
.
NOTE: MIL-T-43548C HAS BEEN CANCELLED
AND REPLACED BY A-A-50199.
(REF. ZT022)
ADDITIONAL INFORMATION FOR MIL-C-43665:
.
INTERIM SPECIFICATION CHANGES TO MIL-C-43665C:
.
PAGE 2, PARA. 3.2, LINE 2, AFTER "TABLE 1 "
INSERT "OR TABLE 1A",
.
PAGE 3, TABLE 1, DELETE "SODIUM (4,5-DICHLORO,
2-CHLOROMETHANE SULFONAMIDO) 3',4'
6',TRICHLORO) DISHENYL ETHER (SEE 6.3.2) 0.26
0.60".
.
PAGE 3, AFTER TABLE 1, INSERT THE FOLLOWING NEW
TABLE:
"TABLE 1A, MOTHPROOFING COMPOUND.
. % ON WEIGHT OF WOOL
. MOTHPROOFING COMPOUND MIN. MAX.
EDOLAN ETS BEFORE DRYCLEANING
*(3-PHENOXYPHENYL) METHYL
PLUS OR MINUS CIS/TRANS 3-(2-,2-
DICCHLOROETHENYL)2,2-
DIMETHYLCYCLORPPANECARBOXYLATE. 0.058 0.40
CIS/TRANS RATIO:MAX.55% PLUS OR--AFTER DRY-CLEAN
MINUS CIS AND MIN.PLUS OR
MINUS TRANS.(*PERMETHRIN) 0.029 0.40
.
PAGE 3,PARA.3.4, LINE 3, AFTER "3.2" INSERT
"TABLE 1".
.
PAGE 3, AFTER PARA. 3.4 INSERT NEW PARAGRAPH AS
FOLLOWS:
"3.4.1 PERCENT OF MOTHPROOFING COMPOUND. THE
PERCENTAGES OF MOTHPROOFING COMPOUND SPECIFIED
IN TABLE 1A SHALL BE BASED ON WEIGHT OF PURE
COMPOUND ON THE WOOL FIBER CONTENT WHEN TESTED
BY HIGH PERFORMANCE LIQUID CHROMATOGRAPH (HPLC)
METHOD, OBTAINABLE FROM BAYER CORP., ROCK HILL,
SC 29732 (SEE 4.2.2)".
.
PAGE 5, PARAGRAPH 4.2.2,TABLE 11,DELETE THE
FOLLOWING:
CHARACTERISTIC REQUIREMENT TEST
. PARAGRAPH METHOD
"SODIUM (4,5-DICHLORO
2-CHLORO-METHANE
SULFONAMIDO)3',4',6',
TRICHLORO) DIPHENYL ETHER 3.4 4.3.1 3/ 4/"
AND SUBSTITUTE THE FOLLOWING:
CHARACTERISTIC REQUIREMENT TEST
. PARAGRAPH METHOD
"EDOLAN ETS
*(3-PHENOXYPHENYL 3.4.1 HPLC 7/
METHYL PLUS OR MINUS CIS/TRANS
3-(2,2-DICHLOROETHENYL)
2,2-DIMETHYL-CYCLOPROPANECARBOXYLATE
CIS/TTRANS RATIO: MAX.55%
PLUS OR MINUS CIS AND MIN.
PLUS OR MINUS TRANS.
*(PERMRTHRIN)"
.
PAGE 5, PARAGRAPH 4.2.2, FOR CHARACTERISTIC
EDOLAN ETS,UNDER TEST METHOD COLUMN, ADD
FOOTNOTE "7"/,ADD NEW FOOTNOTE "8"/.
PAGE 6, PARAGRAPH 4.2.2, TABLE II.AFTER FOOTNOTE
"7/",ADD THE FOLLOWING:"8"/ THE SAMPLE SHALL
BE DRY-CLEANED FOR THREE CYCLES IN ACCORDANCE
WITH AATCC TEST METHOD 86 BEFORE DETERMINING
MOTHPROOFING COMPOUND CONTENT.
.
PAGE 6, PARA.4.2.2, TABLE 11, AFTER FOOTNOTE 6/,
INSERT "7/ HIGH PERFORMANCE LIQUID
CHROMATOGRAPHY (HPLC) TEST METHOD MAY BE
OBTAINED FROM BAYER CORP., ROCK HILL, SC 29732."
.
PAGE 6, PARAGRAPHS 4.3,4.3.1,4.3.1.1,4.3.1.2,
4.3.1.3,4.3.1.4,4.3.1.5 DELETE PARAGRAPHS IN
THEIR ENTIRETY WITH NO REPLACEMENT.
.
PAGE 7, PARAGRAPHS 4.3.1.6, 4.3.1.7, 4.3.1.7.1
DELETE PARAGRAPHS IN THEIR ENTIRETY WITH NO
REPLACEMENT.
.
PAGE 8, PARAGRAPHS 4.3.1.7.2, 4.3.1.8, 4.3.1.8.1
DELETE PARAGRAPHS IN THEIR ENTIRETY WITH NO
REPLACEMENT.
.
.
PAGE 9, PARAGRAPHS 6.3 2, 6.4, 6.5, 6.6 DELETE
PARAGRAPHS IN THEIR ENTIRETY WITH NO
REPLACEMENTS.
.
PAGE 11, DELETE FIGURE 1 IN ITS ENTIRETY WITH NO
REPLACEMENT.
.
PAGE 5
TABLE II, UNDER TEST METHOD: DELETE "2015" AND
SUBSTITUTE "2015.3"
NOTE! MITTEN FF CONC. SUPPLIED BY CIBA-GEIGY
CORP. P.O. BOX 11422, GREENSBORO, NC 27409
.
EDOLAN ETS, SUPPLIED BY MILES INC.,MOBAY ROAD,
PITTSBURGH,PA.15205-9741.
.
ARE APPROVED MOTH PROOFING AGENTS FOR
MILITARY FABRICS.
(Ref. T1118)
ADDITIONAL INFORMATION FOR MIL-C-43791:
.
THE EXTENSIVE DEVIATIONS TO MIL-C-43791B
AND AMEND 1 LISTED BELOW APPLY
EXCLUSIVELY TO AIR FORCE
SLACKS (NSN 8410-01-124-5998) AND AIR
FORCE SHIRT (NSN 8410-01-124-6034)
THE AIR FORCE DESIRES THE PURCHASE OF THE
SUBJECT CLOTH WITHOUT A DURABLE PRESS
FINISH (AND THE RELATED APPLICATION OF A
PRECURED OR POSTCURED RESIN).
DEVIATIONS TO MIL-C-43791B AND AMEND #1
EXCLUSIVELY FOR AIR FORCE SLACKS (
NSN 8410-01-124-5998 AND SHIRT ( 8410-
01-124-6034): PARA. 1. DELETE ALL
REFERENCES TO DURABLE PRESS, PRECURED OR
POSTCURED RESIN APPLICATION AND FINISH.
PARA. 3.1 DELETE AND SUBSTITUTE "3.1 STANDARD
SAMPLE- THE FINISHED CLOTH SHALL MATCH THE
STANDARD SAMPLE FOR SHADE AND APPEARANCE AND
SHALL BE EQUAL TO THE STANDARD SAMPLE WITH
RESPECT TO ALL CHARACTERISTICS FOR WHICH THE
STANDARD SAMPLE IS REFERENCED."
PARA. 3.2.2, 3RD LINE-DELETE "BEFORE TREATMENT",
PARA. 3.3-DELETE AND SUBSTITUTE "COLOR. THE
COLOR OF THE DYED CLOTH SHALL BE BLUE 1577 AND
SHALL MATCH THE STANDARD. THE COLOR SHALL BE
IMPARTED BY SELECTED VAT DYES OR A COMBINATION
OF SELECTED VAT AND DISPERSE DYES AND
APPLIED BY A CONTINUOUS THERMAL FIXATION,STEAM
REDUCTION AND OXIDATION PROCEDURE."
PARA. 3.3.2, 1ST LINE-MATCHING-DELETE "CURED"
AND SUBSTITUTE "FINISHED".
PARA. 3.3.3-DELETE AND SUBSTITUTE "3.3
COLORFASTNESS. THE FINISHED CLOTH SHALL
SHOW COLORFASTNESS TO LAUNDERING(AFTER 3
CYCLES), CROCKING, PERSPIRATION, AND LIGHT
EQUAL TO OR BETTER THAN THE STANDARD SAMPLE.
WHEN NO STANDARD SAMPLE IS AVAILABLE, OR WHEN
THE STANDARD SAMPLE IS NOT REFERENCED FOR
COLORFASTNESS, THE DYED AND FINISHED CLOTH SHALL
SHOW" GOOD" COLORFASTNESS TO LAUNDERING (AFTER 3
CYCLES), PERSPIRATION, LIGHT AFTER 40 HOURS, AND
NO MORE CROCKING THAN MUNSELL VALUE 8.5, WHEN
TESTED AS SPECIFIED IN 4.4."
PARA.3.4, 1ST LINE -DELETE "CURED" AND
SUBSTITUTE "FINISHED".
PARA. 3.5-DELETE AND SUBSTITUTE "3.5 FINISH.
THE CLOTH SHALL BE CLOSELY SINGED, SCOURED,
HEAT SET AND FINISHED TO MEET THE REQUIREMENTS
OF THIS DOCUMENT." PARA. 3.7,3.7.1,3.7.2,3.8,
3.8.1,3.8.2,3.8.3,3.8.4,3.8.4.1-DELETE AND
SUBSTITUTE "PARA. 3.7 DIMENSIONAL STABILITY. THE
CLOTH SHALL NOT SHRINK MORE THAN 2.0 PERCENT IN
THE WARP OR FILLING WHEN TESTED AS SPECIFIED
IN 4.4." PARA. 3.8.5, 2ND LINE-DELETE "CURED".
PARA. 3.9.1 AND 3.9.2 -DELETE AND SUBSTITUTE "3.
9.1 SEAM EFFICIENCY. THE FINISHED CLOTH SHALL
HAVE A SEAM EFFICIENCY OF NO LESS THAN 80
PERCENT WHEN TESTED AS SPECIFIED IN 4.4."
PARA. 3.10, 1ST LINE-DELETE "CURED".
PARA. 3.11-DELETE AND SUBSTITUTE "LENGTH AND
PUT-UP. THE CLOTH SHALL BE FURNISHED ON CONTIN-
UOUS LENGTHS, EACH NOT LESS THAN 40 YARDS. EACH
LENGTH SHALL BE PUT UP ON ROLLS AS SPECIFIED IN
PPP-P-1134."
PARA. 3.14-DELETE IN ITS ENTIRETY.
PARA. 4.2.2.1, LAST PARAGRAPH AT BOTTOM OF PAGE
7, LINE 2-DELETE "30" AND SUBSTITUTE "25"; LINE
3 - DELETE "45" AND SUBSTITUTE "38"; LINE 4-
DELETE "45" AND SUBSTITUTE "38; AND LINE 7-
DELETE "45" AND SUBSTITUTE "38".
PARA. 4.2.2.3-DELETE AND SUBSTITUTE "4.2.2.3
EXAMINATION FOR SHADE. DURING THE YARD-BY-YARD
EXAMINATION, EACH ROLL IN THE SAMPLE SHALL BE
EXAMINED FOR SHADE VARIATION. ANY ROLL IN THE
SAMPLE EXHIBITING UNEVEN SHADE OR SHADE
VARIATION FROM SIDE TO SIDE, SIDE TO CENTER OR
END TO END SHALL BE CAUSE FOR REJECTION OF THE
ENTIRE LOT REPRESENTED BY THE SAMPLE."
PARA. 4.3.1 -DELETE IN ITS ENTIRETY.
PARA. 4.4, SENTENCE 4,5,AND 6- DELETE AND, IN
LIEU THEREOF, SUBSTITUTE " THE SAMPLE UNIT SHALL
BE 3 CONTINUOUS YARDS, FULL WIDTH, OF THE FIN-
ISHED CLOTH." TABLE III. TEST METHODS. DELETE
"(APPLICABLE TO TREATED CLOTH)" IN THE HEADING.
TABLE III. A. 1ST LISTING - DELETE IN ITS
ENTIRETY. B. 2ND LISTING- (1) DELETE "CURED
CLOTH", ITS RELATED REQ'D PARA. AND TEST
METHOD.
(2) DELETE "FROSTING", ITS RELATED REQ'D PARA.
AND TEST METHOD. (3) DELETE "SUBLIMATION", ITS
RELATED REWQ'D PARA. AND TEST METHOD.
C. 8TH LISTING AND SUB-LISTINGS (DIMENSIONAL
STABILITY, ETC.)- DELETE IN ITS ENTIRETY AND
SUBSTITUTE: "DIMENSIONAL STABILITY
WARP 3.7 5556 2/
FILLING 3.7 5556 2/"
D. 9TH, 10TH, 11TH AND 12TH LISTINGS ("
APPEARANCE AFTER....", "CREASE RETENTION....
LAUNDERINGS", "SOIL RELEASE....", "SPRAY RATING,
AFTER ....") - DELETE IN THEIR ENTIRETIES.
E. FOOTNOTE 2/ AND 3/ - DELETE IN THEIR
ENTIRETIES AND, IN LIEU THEREOF, SUBSTITUTE
"2/ COTTON PROCEDURE SHALL BE USED."
PARAS. 4.4.1, 4.4.1.1, 4.4.1.2, 4.4.1.3,
4.4.1.4, 4.4.1.5, 4.4.2, 4.4.3,4.4.3.1,
4.4.3.1.1,4.4.3.1.2,4.4.3.1.3,4.4.3.2,
4.4.3.2.1,4.4.3.2.2,4.4.3.3,4.4.3.3.1,
4.4.3.3.2,4.4.3.3.3. AND 4.4.3.3.4 -DELETE IN
THEIR ENTIRETIES AND, IN LIEU THEREOF,
SUBSTITUTE: "4.4.1 TEST FOR POLYESTER FIBER AND
COTTON FIBER CONTENT - THE GENERAL PROCEDURES OF
TEST METHOD 2100 SHALL BE FOLLOWED AND THE FIBER
CONTENT PERCENTAGES SHALL BE CALCULATED AS
CONTENT PERCENTAGES SHALL BE CALCULATED AS
FOLLOWS:
WEIGHT OF DRY RESIDUAL FIBER X 100 DIVIDED BY:
WEIGHT OF DRY DESIZED SPECIMEN EQUALS PERCENT
POLYESTER
100 MINUS PERCENT POLYESTER EQUALS PERCENT
COTTON. PARA. 4.4.1.1 - REPORT - TWO SPECIMENS
SHALL BE TESTED FROM EACH SAMPLE UNIT AND THE
AVERAGE PERCENT POLYESTER AND THE AVERAGE
PERCENT PERCENT COTTON OF THE TWO SPECIMENS
SHALL BE REPORTED TO THE NEAREST 0.1 PERCENT."
.
ADDITIONAL INFORMATION FOR FED-STD-191:
FED-STD-191A NOTICE 7, DATED AUGUST 9, 2000 IS HEREBY INACTIVE FOR NEW DESIGN. WHEN NOT USING FED-STD-191, SEE INTERIM CHANGES TO END ITEM SPECIFICATION FOR REPLACEMENT ASTM.
INTERIM CHANGES TO FED-STD-191A:
TEST METHOD 5202, PARA. 5.3, DELETE FIRST SENTENCE AND SUBSTITUTE: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH ONE END FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT ONE INCH OF SPECIMEN LIES WITHIN THE CLAMP AND ONE INCH OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (FACE OF THE VISE), AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL PLATE".
TEST METHOD 5309.1 ABRASION RESISTANT OF TEXTILE WEBBING. PAGE 1, PARA 4.1.2,LINE 4: DELETE "B-97" AND SUBSTITUTE "B-91".
THE FOLLOWING METHODS ARE IDENTIFIED AS SPECIFYING OZONE DEPLETING SUBSTANCES: 1100, 1200, 1240, 1400, 1410, 1500, 1510,1520,1530, 1540, AND 1550. PARA 5.1 OF THESE TEST METHODS REQUIRE THE USE OF 1,1,1- TRICHLOROETHANE, ALCOHOL OR ETHER. 1,1,1-TRICHLORETHANE IS AN OZONE DEPLETING SUBSTANCE (METHYL CHLOROFORM) AND IS THEREFORE PROHIBITED. THE USE OF EITHER ALCOHOL OR ETHER IS REQUIRED WHEN THESE METHODS ARE IN BASIC OR ANY REFERENCED DOCUMENT.
METHOD 5202, STIFFNESS OF CLOTH, DIRECTIONAL; CANTILEVER BENDING METHOD. PAGE 2, PARA. 5.3 DELETE FIRST SENTENCE AND SUBSTITUTE WITH THE FOLLOWING: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH 1 END FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT 1" OF THE SPECIMEN LIES WITHIN THE CLAMP AND 1" OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (INNER FACE OF THE VISE) AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL PLATE."
METHOD 5556.1, MOBILE LAUNDRY EVALUATION FOR TEXTILE MATERIALS, PAGE 5, PARA. 5.2.2, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND PLACED IN A PRE-HEATED DRYER HAVING A STACK TEMPERATURE OF 140-180 DEG. F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 45-60 MINUTES OR UNTILSAMPLES ARE DRY IN A ROTATING TUMBLE DRYER."
PAGE 5, PARA. 5.2.3, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THEFOLLOWING: "THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND PLACED IN A PRE-HEATED DRYER HAVING A STACKTEMPERATURE OF 140-180 DEG. F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 35-40 MINUTES OR UNTIL SAMPLES ARE DRY."
METHOD 5931, ELECTROSTATIC DECAY OF FABRICS; DETERMINATION OF PAGE 1, PARA. 3: AFTER NUMBER OF DETERMINATIONS ADD "PER SAMPLE UNIT". PAGE 1, PARA. 4: DELETE "APPARTUS" AND SUBSTITUTE "APPARATUS". PAGE 1, PARA. 5.1, LINE 3: AFTER "AT" DELETE"APPROXIMATELY".
PAGE 2, PARA. 5.2, LINES 2, AND 5: AFTER "OF" ADD "+-". LINE 6: AFTER "TO" ADD "+-".
PAGE 2, PARA. 5.3: DELETE IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING:"5.3 MOUNT A SPECIMEN TIGHTLY ACROSS THE ELECTRODES, CENTERING IT OVER THE SENSOR OPENING. THE SURFACE OF THE TEST SPECIMEN (BACK OR FRONT) SHALL FACE THE SENSOR. RECORD (OPTIONAL) THE RESIDUAL CHARGE LEVEL ON THE SAMPLE AS SEEN BY THE SENSOR, INCLUDING POLARITY.
NOTE THAT TEST SAMPLES WITH THE RESIDUAL CHARGE LEVELS OF LESS +500 VOLTS YIELD THE BEST RESULTS. APPLY +5000 VOLTS TO THEELECTRODES FOR A PERIOD OF 20 SECS. AT THE END OF THE 20 SECOND PERIOD, THE HIGH VOLTAGE (5000 VOLTS) SHALL BE TURNED OFF ANDTHE SPECIMENS IMMEDIATELY GROUNDED. THE VOLTAGE BEHAVIOR OF THE SPECIMEN WITH RESPECT TO TIME SHALL BE PLOTTED ON THE RECORDER. NOTE: IN SOME CASES, THE TEST EQUIPMENT WILL DISPLAY VOLTAGE AND DECAY TIME INFORMATION AND A CHART RECORDER IS NOT NECESSARY."
PAGE 2, PARA. 5.4, LINE 3: DELETE SENTENCE BEGINNING WITH "IF THE SPECIMEN DID" IN ITS ENTIRETY.
PAGE 2, PARA. 5.5: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "RECORD THE MAXIMUM VOLTAGE LEVEL(INCLUDING POLARITY) AND DECAY TIME TO 10% OF THE MAXIMUM VOLTAGE LEVEL ACHIEVED."
PAGE 2, PARA. 5.6, LINE 1: ADD THE FOLLOWING PRIOR TO 1ST SENTENCE: "REVERSE VOLTAGE POLARITY REPEAT MEASUREMENT, ANDRECORD RESULTS."
PAGE 3, PARA. 6.6: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE AVERAGE TIME TO DECAY TO 10%OF THE MAX VOLTAGE SHALL BE INCLUDED FOR EACH OF THE WARP & FILLING DIRECTIONS, AS WELL AS THE OVERALL AVERAGE, FOR EACHFABRIC TESTED. THESE WILL BE OBTAINED BY AVERAGING THE TEST RESULTS (ABSOLUTE VALUE OF) TOGETHER FOR BOTH VOLTAGEPOLARITIES. UNLESS OTHERWISE STATED IN THE REQUIREMENTS DOCUMENT, THE FABRIC SHALL BE CONSIDERED ACCEPTABLE IF THEAVERAGE MAXIMUM VOLTAGE IN BOTH THE WARP AND FILLING DIRECTIONS IS LESS THAN 4000 VOLTS, AND THE AVERAGE DECAY TIME (TO 10% MAXVOLTAGE) IS GREATER THAN 0.5 SECONDS IN BOTH THE WARP AND FILLING DIRECTIONS. IT SHALL BE INDICATED WHETHER THE FABRIC ISACCEPTABLE OR NON-ACCEPTABLE."
PAGE 3, PARA. 7.1, SECOND COLUMN, LINE 2: DELETE 406C AND SUBSTITUTE WITH "406D".
AFTER PARA. 7.1, ADD THE FOLLOWING: "7.2 NOTE: IF THE MODEL 406D STATIC DECAY METER, OR EQUIVALENT, IS USED, A CHART RECORDER ISNOT MANDATORY FOR THE TEST."
(Ref. T0215)
ADDITIONAL INFORMATION: FED-STD-751 HAS BEEN
CANCELLED AND REPLACED BY ASTM-D-6193, 4/98
STANDARD PRACTICES FOR STITCHES AND SEAMS.
THIS STANDARD SHOULD BE USED IN PREFERENCE
TO FED-STD-751.
(ref. T0216 - May 18, 2006)
MIL-STD-129R - DEPARTMENT OF DEFENSE STANDARD PRACTICE
- MILITARY MARKING FOR SHIPMENT AND STORAGE
DATED 18 FEBRUARY 2014
INTERIM CHANGES:
OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS
IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:
THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.
IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.
ADDITIONAL INFORMATION FOR MIL-STD-1491:
.
NO ADDITIONAL INFORMATION FOLLOWS..
1
ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4:
NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED.
APPLICATION FOR COPIES SHOULD BE ADDRESSED TO:
AMERICAN SOCIETY FOR QUALITY
600 NORTH PLANKINTON AVENUE
MILWAUKEE, WISCONSIN 53203
(Ref. T0795 - May 17, 2006)
INSPECTION TEXT
PRESERVATION AND PACKING SHALL BE IAW
ASTM-D-3951.
SIGNIFICANT NOTE - "PALLETIZATION IS REQUIRED FOR THESE SUPPLIES".
NOTE: THE FOLLOWING APPLIES TO ALL NON-MANUFACTURED WOOD PACKAGING MATERIALS:
"All Wood Packaging Material (WPM) acquired by DOD must meet requirements of International Standards for Phytosanitary Measures (ISPM) 15, "Guidelines for Regulating Wood Packaging Materials in International Trade." DOD shipments inside and outside of the United States must meet ISPM 15 whenever WPM is used to ship DOD cargo, or when wood is being acquired by DLA for future use as packaging material. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frame and cleats. Packaging materials exempt from the requirements are materials that have undergone a manufacturing process, such as corrugated fiberboard, plywood, particleboard, veneer, and oriented strand board (OSD). All WPM shall comply with one of the following official quality control programs:
Heat Treatment (HT) or Kiln Dried Heat Treatment (KD HT) in accordance with American Lumber Standard Committee, Incorporated (ALSC) Wood Packaging Material Program and WPM Enforcement Regulations (see http://www.alsc.org/; or
All WPM shall include certification/quality markings in accordance with the ALSC or NWPCA standards, as applicable. Markings shall be placed in an unobstructed area that will be readily visible to inspectors. Pallet markings shall be applied to the stringer or block on diagonally opposite sides of the pallet and be contrasting and clearly visible.
All containers shall be marked on a side other than the top or bottom, contrasting and clearly visible. All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ASLC approved DUNNAGE stamp. Failure to comply with the requirements of this restriction may result in refusal, destruction, or treatment of materials at the point of entry. The Agency reserves the right to recoup from the Contractor any remediation costs incurred by the Government."
PALLET SHALL BE 4 WAY ENTRY, WINGED TYPE. PALLETIZED LOAD DIMENSIONS SHALL NOT EXCEED 43 INCHES IN LENGTH, 52 INCHES IN WIDTH, AND 54 INCHES IN HEIGHT (INCLUDING THE PALLET).
THE PALLETIZED LOAD SHALL BE BONDED USING APPROVED COMMERCIAL BONDING MATERIALS. THE USE OF METAL BANDING, IN SECURING BOXES TO PALLETS, IS DISCOURAGED. PALLET LOADS SHALL CONTAIN THE SAME NUMBER OF CARTONS, OF IDENTICAL QUANTITIES, OF ONE NSN, TO THE MAXIMUM EXTENT POSSIBLE.
PALLET LOADS CONTAINING MORE THAN ONE NSN SHALL BE CLEARLY MARKED TO LIST ALL THE NSN'S CONTAINED IN THE LOAD. NO CARTON SHALL HAVE MORE THAN ONE NSN. AT THE END OF A SIZE RUN, NO MORE THAN ONE CARTON PER NSN MAY BE SHORT OR OVER THE SPECIFIED QUANTITY. SAID CARTON SHALL BE CLEARLY MARKED "SHORT" OR "OVER".
MIL-STD-147 IS REFERENCED FOR PALLETIZED LOADS.
IN ADDITION TO REQUIREMENTS SPECIFIED ABOVE THE FOLLOWING CLAUSE ALSO APPLIES:
52.247-9012 - REQUIREMENTS FOR TREATEMENT OF WOOD PACKAGING MATERIALS (WPM) - (JULY 2006)
THE GOVERNMENT ASSIGNED UNIVERSAL PRODUCT
CODE (UPC) MUST BE PLACED ON ALL SHIPPING
CARTONS ON WHICH THE NSN APPEARS".
DLA Troop Support reserves the right to include the following clause in the upcoming solicitation:
52.216-9006 ADDITION/DELETION OF ITEMS (AUG 2005) DLAD
CLINS 0001 and 0002 listed in the above item description are the core items that will be solicited in the
universe known as sweaters, various items. DLA Troop Support also reserves the right to add additional sweaters
to the contract by via the above referenced ADD/DELETE clause. Below are a list of the core NSNs that will be
included in the upcoming solicitation for the universe of items:
NSN Nomenclature Size
8405014969808 SWEATER,MC 28/30R
8405014969809 SWEATER,MC 32R
8405014969810 SWEATER,MC 34R
8405014969811 SWEATER,MC 36R
8405014969813 SWEATER,MC 38R
8405014969814 SWEATER.MC 40R
8405014969816 SWEATER,MC 42R
8405014969820 SWEATER.MC 44R
8405014969822 SWEATER,MC 46R
8405014969823 SWEATER,MC 48R
8405014969824 SWEATER,MC 50R
8405014456907 SWEATER,CG 34R
8405014456918 SWEATER,CG 36R
8405014456920 SWEATER,CG 38R
8405014456923 SWEATER,CG 40R
8405014456925 SWEATER,CG 42R
8405014456959 SWEATER,CG 44R
8405014457006 SWEATER,CG 46R
8405014457010 SWEATER,CG 48R
8405014457022 SWEATER,CG 50R
8405014620727 SWEATER,CG 28R
8405014626724 SWEATER,CG 30R
8405014620728 SWEATER,CG 32R
POTENTIAL ADD ON NSNs
FSC Nomenclature Size
8405 Sweater, Navy X-SMALL
8405 Sweater, Navy SMALL
8405 Sweater, Navy MEDIUM
8405 Sweater, Navy LARGE
8405 Sweater, Navy X-LARGE
8405 &n
